Cart 0

WiFi Shield V3 For Arduino PCB Antenna (802.11b/g/n)

Deliveryfrom just £2.50

20,000+customer reviews

No Quibblereturns policy

Securepayment system

Next Day DeliveryOrder by 2PM*

Sold Out
£52.00

We will notify you when this product becomes available.


*PreOrder Details

Share this Product


DFRobot WiFi Shield, is part of our wireless family product. This WIFI Shield V3 supports AP + STA dual mode, and is extremely easy to connect to a home router network. You only need a mobile phone or Pad to log in the AP network of this module (similar way with some router configuration tool). After logging in the module and set the Wireless name, it is ready to connect the WIFI network (No AT command setup required, which is often very complex).
 
This module uses dynamic power management to achieve low power consumption capability (standby:
  • Working voltage: 5V
  • Frequency range: 2.4 - 2.497GHz
  • Output power: 16dBm
  • Transmission rate: 54Mbps - 1Mbps
  • Transmission distance:
  • Size: 55 × 53 × 11mm(2.16x2.09x0.43")
  • Weight: 40g
  • Support IEEE 802.11b/g/n
  • Support AP, Client, Gateway and UART to WLAN mode and so on
  • Support DHCP, automatic access to IP; Support allocating IP to slave device in AP mode
  • Support network protocol: TCP/ UDP/ ARP/ ICMP/ HTTP/ DNS/ DHCP
  • Optional working modes: TCP Server/ TCP Client/ UDP; Support up to 32 Client in TCP Server mode
  • Support most of WIFI encryption algorithm: WEP/ WAP-PSK/ WAP2-PSK/ WAPI; Type of encryption: WEP64/ WEP128/ TKIP/AES
  • Support transparent UART/protocol data transmission mode; Up to 1M cache space; Highest baud rate: 460800bps
  • Support UART(TTL) to wireless applications
  • Drag down the level of the Reload IO pin for one sencod, you can restore factory settings. So do not worry about the wrong settings.
  • Support running in AP mode and the node (Station) mode;The real hardware AP, so Android can directly access it.
  • Provide AT command configuration
  • Provide the friendly web configuration page, and can be configured by webpage
  • Serial frame delay and the amount of data can be set.
  • Support routing/bridge mode network architecture
  • Designed by standard Arduino stack, and can be easily put on the standard Arduino, MEGA, Romeo board or shield

DOCUMENTS

  • WiKi Doc
  • Schematic
  • User Manual (Included AT commend)
  • WiFi Firmware (V1.0.5)

SHIPPING LIST

  • WIFI Shield V3(PCB Antenna)   ×1

PROJECTS

  • Discussion and extended info ( Forum )

  • Working voltage: 5V
  • Frequency range: 2.4 - 2.497GHz
  • Output power: 16dBm
  • Transmission rate: 54Mbps - 1Mbps
  • Transmission distance:
  • Size: 55 × 53 × 11mm(2.16x2.09x0.43")
  • Weight: 40g
  • Support IEEE 802.11b/g/n
  • Support AP, Client, Gateway and UART to WLAN mode and so on
  • Support DHCP, automatic access to IP; Support allocating IP to slave device in AP mode
  • Support network protocol: TCP/ UDP/ ARP/ ICMP/ HTTP/ DNS/ DHCP
  • Optional working modes: TCP Server/ TCP Client/ UDP; Support up to 32 Client in TCP Server mode
  • Support most of WIFI encryption algorithm: WEP/ WAP-PSK/ WAP2-PSK/ WAPI; Type of encryption: WEP64/ WEP128/ TKIP/AES
  • Support transparent UART/protocol data transmission mode; Up to 1M cache space; Highest baud rate: 460800bps
  • Support UART(TTL) to wireless applications
  • Drag down the level of the Reload IO pin for one sencod, you can restore factory settings. So do not worry about the wrong settings.
  • Support running in AP mode and the node (Station) mode;The real hardware AP, so Android can directly access it.
  • Provide AT command configuration
  • Provide the friendly web configuration page, and can be configured by webpage
  • Serial frame delay and the amount of data can be set.
  • Support routing/bridge mode network architecture
  • Designed by standard Arduino stack, and can be easily put on the standard Arduino, MEGA, Romeo board or shield

  • WiKi Doc
  • Schematic
  • User Manual (Included AT commend)
  • WiFi Firmware (V1.0.5)

Share this Product


More from this collection